Network Cabling Burbank, CA | Cat6, Cat6A Installer
Network cabling in Burbank
The most common cabling call we get from Burbank is a business that grew into its space and now has a patch panel nobody can trace, a switch on the floor of the copy room and a few desks running on long patch cords across the carpet. Post houses on Alameda and Olive need clean Cat6A between edit bays and the machine room.
Book a free Burbank site survey Call (442) 222-2775 Text usNetwork Cabling done right for Burbank businesses
Offices Downtown want drops added without tearing up the ceiling. Warehouses near Hollywood Burbank Airport need cable that reaches the far dock and survives forklifts.
We run Cat6 and Cat6A in Burbank offices, production space, medical suites, schools and industrial buildings. That means a survey of your pathways, plenum-rated cable where the code requires it, proper support above the ceiling, a labeled patch panel and a printed test report for every run. If the closet needs a real rack, cable management and power, we do that too. The job starts with a free site survey at your address.
We terminate to TIA-568-B, keep bends and bundles within spec, and separate low voltage from power. Plenum cable goes above drop ceilings that carry return air, riser cable between floors. Every run is documented so the next tech — ours or yours — can find it in a minute.
What is included
- Cat6 and Cat6A structured cabling, plenum or riser rated to match your ceiling and code
- Patch panels, racks, cable management and a labeled, documented closet
- Certification testing on every drop with a printed test report
- Voice, data, PoE camera and access-point drops on the same run
- Conduit, J-hooks and pathways that pass inspection
- Moves, adds and changes after the install without a full re-pull
Free site survey in Burbank
We walk the property, count what you need and give you an itemized quote — free, no obligation.
Book itServing all of Burbank
ZIP codes 91501, 91502, 91504, 91505, 91506. Nearby: Glendale, Los Angeles, Pasadena, San Fernando, Santa Clarita.
Network Cabling across Burbank
Media District buildings on Olive Avenue, Alameda Avenue and Riverside Drive tend to have older hard-lid ceilings and risers full of prior tenants' cable, so we plan pathways before quoting. Downtown offices above San Fernando Boulevard usually have drop ceilings and shared telecom rooms managed by the landlord. Out by the airport on Winona, Ontario and Empire, the tilt-ups need long home runs, J-hooks along the rafters and sometimes fiber to a second IDF. Magnolia Park storefronts are small but old, with shared walls that need care. We reach all of it from the 5 and the 134.
Survey, install, document
Survey
We walk the space, count drops, trace pathways and check the closet, power and ceiling type. Free, and usually the same week.
Install
Cable is pulled in bundles, dressed, terminated to TIA-568 standards and labeled at both ends.
Certify
Every drop is tested with a certifier and you get the report, a drawing and photos of the closet.
Network Cabling in Burbank — questions we get
Should my Burbank office use Cat6 or Cat6A cabling?
Cat6 handles most Burbank offices and retail at 1 Gbps with room for 2.5 Gbps. Cat6A is worth it for post-production, edit suites and media offices on Alameda and Olive that move large files, and for Wi-Fi 6E and 7 access points. We often mix the two: Cat6A to access points and machine rooms, Cat6 to desks. The free site survey settles it.
Can you add network drops in an occupied Burbank office without shutting us down?
Yes. Most Downtown Burbank and Media District jobs happen while the business is open, with drilling and ceiling work done early, late or on a weekend when the landlord requires it. We stage cable off the floor, keep dust contained and cut over desks one at a time so nobody loses a workday. Ask about after-hours scheduling during the free site survey.
Do you certify and label network cabling in Burbank?
Every run. We test each Cat6 or Cat6A drop, label both ends to match the patch panel and hand you a report. Burbank landlords and IT managers use that report when tenants change or when a link acts up. If an old building near the airport or Downtown has unlabeled cable from earlier tenants, we can trace, tone and document it as part of the job.
How long does a network cabling install take?
A typical office of 20 to 60 drops is one to three days. Larger buildouts are scheduled in phases so your team keeps working. After the free site survey you get a firm schedule with the itemized quote.
Cat6 or Cat6A — which should I choose?
Cat6 handles 1 Gbps at 100 meters and 10 Gbps at short runs, and is the right choice for most offices. Cat6A carries 10 Gbps the full distance and supports higher-power PoE, so we recommend it for new builds, Wi-Fi 6E/7 access points and anything you plan to keep for 15 years.
Do you label and test every cable?
Yes. Every drop is labeled at the jack and the patch panel, certified with a tester, and you receive the test report. Untested cabling is where intermittent network problems come from, so we do not skip it.
Other low voltage services in Burbank
Industries we serve in Burbank
Local guide: Security camera rules, permits and placement for Burbank businesses (2026 guide)
Let's walk your Burbank property — on us
Fill out the form and you will hear from us fast — usually the same day. Or skip the typing:
Call or text (442) 222-2775 — we answer.
Text us · Email tech@itech2.co
Have a question first? Read the FAQ or see who does the work.
Main office line: (866) 904-8787 · Licensed C-7 #1098090 · Since 2010